для размещения заказа - sgs@sgs-tool.ru Speed & Feed Recommendations Z1M, Z1MB HARDNESS CUT SPEED FEED (mm/flute) Metric BRINELL Type m/min 3 6 10 12 20 25 Slot 154 0.0091 0.024 0.051 0.060 0.080 0.088 Profile 192 0.0091 0.024 0.080 0.088 CARBON STEEL 175 Light 317 0.0206 0.055 0.051 0.060 0.184 0.200 1018, 1040, 1080, 1090, Slot 134 0.0091 0.024 0.080 0.088 10L50, 1140, 1212, 12L15, > 175 Profile 168 0.0091 0.024 0.115 0.137 0.080 0.088 1525, 1536 275 Light 278 0.0206 0.055 0.184 0.200 Slot 113 0.0067 0.019 0.051 0.060 0.061 0.065 Profile 141 0.0067 0.019 0.061 0.065 Light 233 0.0156 0.041 0.051 0.060 0.139 0.150 Slot 77 0.0067 0.019 0.061 0.065 Profile 96 0.0067 0.019 0.115 0.137 0.061 0.065 Light 158 0.0156 0.041 0.139 0.150 Slot 73 0.0060 0.017 0.037 0.046 0.053 0.058 Profile 91 0.0060 0.017 0.053 0.058 ALLOY STEEL 275 Light 151 0.0137 0.036 0.037 0.046 0.120 0.133 4140, 4150, 4320, 5120, Slot 45 0.0048 0.012 0.043 0.045 5150, 8630, 86L20, 50100 > 275 Profile 56 0.0048 0.012 0.085 0.103 0.043 0.045 375 Light 93 0.0108 0.029 0.096 0.105 Slot 108 0.0084 0.022 0.037 0.046 0.075 0.083 Profile 135 0.0084 0.022 0.075 0.083 Light 223 0.0194 0.053 0.037 0.046 0.173 0.190 Slot 80 0.0084 0.022 0.075 0.083 Profile 101 0.0084 0.022 0.085 0.103 0.075 0.083 Light 166 0.0194 0.053 0.173 0.190 Slot 138 0.0065 0.017 0.032 0.041 0.059 0.063 Profile 173 0.0065 0.017 0.059 0.063 TOOL STEEL 250 Light 286 0.0149 0.041 0.032 0.041 0.133 0.145 A2, D2, H13, L2, M2, Slot 96 0.0053 0.014 0.045 0.050 P20, S7, T15, W2 > 250 Profile 120 0.0053 0.014 0.075 0.091 0.045 0.050 375 Light 198 0.0120 0.031 0.107 0.115 Slot 88 0.0053 0.014 0.027 0.031 0.045 0.050 Profile 110 0.0053 0.014 0.045 0.050 Light 181 0.0120 0.031 0.027 0.031 0.107 0.115 Slot 52 0.0048 0.012 0.043 0.045 Profile 65 0.0048 0.012 0.061 0.072 0.043 0.045 Light 108 0.0108 0.029 0.096 0.105 Slot 19 0.0036 0.010 0.048 0.058 0.032 0.035 Profile 24 0.0036 0.010 0.032 0.035 220 Light 40 0.0082 0.022 0.048 0.058 0.075 0.080 > 220 CAST IRON 260 0.109 0.130 Gray, Malleable, Ductile 275 0.048 0.058 STAINLESS (free machining) 275 303, 416, 420F, 430F, 440F 0.048 0.058 325 STAINLESS (difficult) 0.109 0.130 304, 304L, 316, 316L 350 0.037 0.043 STAINLESS (PH) 300 17-4PH, 15-5PH, Custom 0.037 0.043 450, 16-6PH, PH13-8Mo 0.083 0.098 TITANIUM Ti5Al-5V-5Mo, 0.029 0.034 Ti6Al4V, Ti-7Al4Mo 0.029 0.034 HIGH TEMPERATURE ALLOY A-286, Hastelloy, Incoloy, 0.067 0.079 Inconel, Rene, Waspalloy 0.029 0.034 0.029 0.034 0.067 0.079 0.027 0.031 0.027 0.031 0.061 0.072 0.021 0.024 0.021 0.024 0.045 0.055 SLOT CUT TYPE LIGHT* rpm = (1000 x m/min) / (3.14 x D1) PROFILE ipm = (mm/flute) x 4 x rpm Rw = D1 Rw = .05 x D1 Ad = D1 Rw = .5 x D1 Ad = L2 • maximum recommended depths shown Ad = 1.5 x D1 • reduce speed and feed for materials harder than listed * finish cuts typically require reduced feed and cutting depths of .02 x D1 maximum •refer to the SGS Tool Wizard for more complete technical information (available at ) 60 sgs@sgs-tool.ru END MILLS www.sgs-tool.ru END MILLS