Фрезы и прочий твердосплавный инструмент
SGS-Tools - Полный каталог инструмента - 2013 EN
для размещения заказа - sgs@sgs-tool.ru
Speed & Feed Recommendations
Z1, Z1B, Z16CR HARDNESS CUT SPEED 1/8 1/4 FEED (inch/flute) 3/4 1
Fractional BRINELL
Type sfm 0.00038 0.0010 3/8 1/2 0.0030 0.0035
CARBON STEEL 175 0.00038 0.0010 0.0030 0.0035
1018, 1040, 1080, 1090, Slot 505 0.00086 0.0023 0.0019 0.0025 0.0069 0.0080
10L50, 1140, 1212, 12L15, > 175 Profile 630 0.00038 0.0010 0.0019 0.0025 0.0030 0.0035
1525, 1536 275 Light 1040 0.00038 0.0010 0.0043 0.0057 0.0030 0.0035
Slot 440 0.00086 0.0023 0.0019 0.0025 0.0069 0.0080
ALLOY STEEL 275 Profile 550 0.00028 0.0008 0.0019 0.0025 0.0023 0.0026
4140, 4150, 4320, 5120, Light 910 0.00028 0.0008 0.0043 0.0057 0.0023 0.0026
5150, 8630, 86L20, 50100 > 275 Slot 370 0.00065 0.0017 0.0014 0.0019 0.0052 0.0060
375 Profile 465 0.00028 0.0008 0.0014 0.0019 0.0023 0.0026
Light 765 0.00028 0.0008 0.0032 0.0043 0.0023 0.0026
TOOL STEEL 250 Slot 250 0.00065 0.0017 0.0014 0.0019 0.0052 0.0060
A2, D2, H13, L2, M2, Profile 315 0.00025 0.0007 0.0014 0.0019 0.0020 0.0023
P20, S7, T15, W2 > 250 Light 520 0.00025 0.0007 0.0032 0.0043 0.0020 0.0023
375 Slot 240 0.00057 0.0015 0.0012 0.0017 0.0045 0.0053
Profile 300 0.00020 0.0005 0.0012 0.0017 0.0016 0.0018
CAST IRON 220 Light 495 0.00020 0.0005 0.0028 0.0038 0.0016 0.0018
Gray, Malleable, Ductile > 220 Slot 145 0.00045 0.0012 0.0010 0.0013 0.0036 0.0042
260 Profile 185 0.00035 0.0009 0.0010 0.0013 0.0028 0.0033
STAINLESS (free machining) 275 Light 305 0.00035 0.0009 0.0023 0.0030 0.0028 0.0033
303, 416, 420F, 430F, 440F Slot 355 0.00081 0.0022 0.0018 0.0024 0.0065 0.0076
275 Profile 445 0.00035 0.0009 0.0018 0.0024 0.0028 0.0033
STAINLESS (difficult) Light 730 0.00035 0.0009 0.0041 0.0054 0.0028 0.0033
304, 304L, 316, 316L 325 Slot 265 0.00081 0.0022 0.0018 0.0024 0.0065 0.0076
Profile 330 0.00027 0.0007 0.0018 0.0024 0.0022 0.0025
STAINLESS (PH) 350 Light 545 0.00027 0.0007 0.0041 0.0054 0.0022 0.0025
17-4PH, 15-5PH, Custom Slot 455 0.00062 0.0017 0.0014 0.0018 0.0050 0.0058
450, 16-6PH, PH13-8Mo 300 Profile 570 0.00022 0.0006 0.0014 0.0018 0.0017 0.0020
Light 935 0.00022 0.0006 0.0031 0.0041 0.0017 0.0020
TITANIUM Slot 315 0.00050 0.0013 0.0011 0.0014 0.0040 0.0046
Ti5Al-5V-5Mo, Profile 395 0.00022 0.0006 0.0011 0.0014 0.0017 0.0020
Ti6Al4V, Ti-7Al4Mo Light 650 0.00022 0.0006 0.0025 0.0033 0.0017 0.0020
Slot 290 0.00050 0.0013 0.0011 0.0014 0.0040 0.0046
HIGH TEMPERATURE ALLOY Profile 360 0.00020 0.0005 0.0011 0.0014 0.0016 0.0018
A-286, Hastelloy, Incoloy, Light 595 0.00020 0.0005 0.0025 0.0033 0.0016 0.0018
Inconel, Rene, Waspalloy Slot 170 0.00045 0.0012 0.0010 0.0013 0.0036 0.0042
Profile 215 0.00015 0.0004 0.0010 0.0013 0.0012 0.0014
Light 355 0.00015 0.0004 0.0023 0.0030 0.0012 0.0014
Slot 65 0.00034 0.0009 0.0008 0.0010 0.0028 0.0032
Profile 80 0.0008 0.0010
Light 130 0.0017 0.0023
SLOT CUT TYPE LIGHT* rpm = sfm x 3.82 / D1
PROFILE ipm = (inch/flute) x 4 x rpm
Short, Regular Short, Regular
Rw = D1 Short Regular Rw = .05 x D1 • maximum recommended depths shown
Ad = D1 Rw = .5 x D1 Rw = .5 x D1 Ad = L2 • reduce speed and feed for materials harder
Ad = L2 Ad = 1.5 x D1
than listed
* finish cuts typically require reduced feed
and cutting depths of .02 x D1 maximum
•refer to the SGS Tool Wizard for more
complete technical information
(available at )
END MILLS END MILLS 59
sgs@sgs-tool.ru
www.sgs-tool.ru