Ниже представлена эта же страница в формате, позволяющем производить копирование текста.

SGS-Tools - Полный каталог инструмента - 2013 EN

                                          для размещения заказа - sgs@sgs-tool.ru

                                           Speed & Feed Recommendations

           ZH1CR                HARDNESS                CUT     SPEED              1/4     3/8   FEED (inch/flute)    3/4       1
         Fractional              BRINELL                Type     sfm                                     1/2
                                                                                 0.0007  0.0012                     0.0020  0.0023
                                                        Slot     70              0.0007              0.0017                 0.0023
                                                       Profile   85              0.0015                                     0.0053
                                 300                  Light     145             0.0005  0.0012  0.0017             0.0020  0.0016
                                > 300                   Slot     55              0.0005                                     0.0016
 H IGH TEMPERATURE ALLOY                            Profile   70              0.0011  0.0028  0.0038             0.0045  0.0037
     A-286, Hastelloy, Haynes,                         Light     110
     Incoloy, Inconel, Rene,                                                             0.0009  0.0012             0.0014     25
     Udimet, Waspalloy
                                                                                                                            0.058
                                                                                         0.0009  0.0012             0.0014  0.058
                                                                                                                            0.133
                                                                                         0.0020  0.0026             0.0032  0.040
                                                                                                                            0.040
         ZH1MCR                 HARDNESS                CUT     SPEED               6      10    FEED (mm/flute)      20    0.093
          Metric                 BRINELL                Type    m/min                                    12
                                                                                 0.017   0.032                      0.053
 H IGH TEMPERATURE ALLOY      300                   Slot     21              0.017   0.032        0.041         0.053
     A-286, Hastelloy, Haynes,  > 300                  Profile   27              0.036   0.075        0.041         0.120
     Incoloy, Inconel, Rene,                           Light     45              0.012   0.024        0.091         0.037
     Udimet, Waspalloy                                  Slot     16              0.012   0.024        0.029         0.037
                                                       Profile   21              0.026   0.053        0.029         0.085
                                                       Light     34                                   0.062

         SLOT                                CUT TYPE                          LIGHT*    rpm = sfm x 3.82 / D1
                                              PROFILE                                    rpm = (1000 x m/min) / (3.14 x D1)
Rw = D1                                                         Rw = .05 x D1            ipm = (inch/flute) x 4 x rpm
Ad = D1                         Rw = .5 x D1                    Ad = 1.5 x D1            mm/min = (mm/flute) x 4 x rpm
                                Ad = 1.5 x D1
                                                                                         • maximum recommended depths shown
                                                                                         • reduce speed and feed for materials harder

                                                                                           than listed
                                                                                         * finish cuts typically require reduced feed and

                                                                                           cutting depths of .02 x D1 maximum
                                                                                         • refer to the SGS Tool Wizard for more complete

                                                                                           technical information
                                                                                           (available at )

               END MILLS                                                                         END MILLS                                  61

                                                                sgs@sgs-tool.ru
                                                                www.sgs-tool.ru
Заявка