Фрезы и прочий твердосплавный инструмент
SGS-Tools - Инструмент для работы по алюминию APR и APF - 2015 EN
для размещения заказа - sgs@sgs-tool.ru
|Fractional & Metric Speed & Feed Recommendations
Ap
Series Ae Ae Vc Diameter (D1)
S-Carb APR Ae x D1 Ap x D1 (sfm) (inch)
Fractional 3280
(2624-3936) 3/4 1
Slot <40hp 1 1 4920 RPM 16706 12530
(3936-5904) Fz 0.0060 0.0070
ALUMINUM ALLOYS Slot >67hp 1 1 6560 301 263
N 2024, 5052, 5086, 6061, 6063, Profile 0.5 1.5 (5248-7872) Feed (IPM) 25059 18794
2620 RPM 0.0090 0.0110
7075 (2096-3144) Fz
3940 677 620
ALUMINUM ALLOYS Slot <40hp 1 1 (3152-4728) Feed (IPM)
(LITHIUM)* Slot >67hp 1 1 4920 33412 25059
N 2090, 2091, 2099, 2195, 2199, 0.5 1.5 (3936-5904) RPM 0.0090 0.0110
Profile Fz
2297, 8090 902 827
Feed (IPM) 13345 10008
RPM 0.0060 0.0070
Fz 240 210
20068 15051
Feed (IPM) 0.0090 0.0110
RPM 542 497
Fz 25059 18794
0.0090 0.0110
Feed (IPM) 677 620
RPM
Fz
Feed (IPM)
Note: • maximum recommended depths shown
• surface speed is dependent on machine spindle & fixturing* • reduce speed and feed for materials harder than listed
• balancing is recommended at ultra high surface speeds • ramp angle = 15 (feed rate = 30%)
• tool life may be reduced when machining Lithium Alloys • maximum ramp depth = 1 x D1
• rpm = sfm x 3.82 / D1 • plunge depth = 1 x D1 (feed rate = 30%)
• ipm = (inch / flute) x number of flutes x rpm •
Ap
Series Ae Ae Vc Diameter (D1)
S-Carb APR Ae x D1 Ap x D1 (m/min) (mm)
Metric
1000 12 16 20 25
(800-1200) 26525 12732
Slot <30 kW RPM 0.080 19894 15915 0.180
1500 Fz 6366 6875
11 (1200-1800) 39788 0.110 0.150 19098
Feed (mm/min) 0.120 6565 7162 0.270
ALUMINUM ALLOYS Slot >50kW 1 1 2000 RPM 29841 23873
N 2024, 5052, 5086, 6061, 6063, Profile 0.5 1.5 (1600-2400) Fz 14324 0.160 0.220 15469
7075 800 Feed (mm/min) 53050 14324 15756 25464
(640-960) 0.120 0.270
RPM 19098 39788 31830 20626
1200 Fz 21220 10186
(960-1440) 0.080 0.160 0.220 0.180
Feed (mm/min) 5093 5500
1500 RPM 3830 19098 21008 15278
(1200-1800) Fz 0.120 0.270
Slot <30 kW 1 1 11459 15915 12732 12375
1 Feed (mm/min) 39788 0.110 0.150 19098
ALUMINUM ALLOYS Slot >50kW 1.5 RPM 0.120 5252 5729 0.270
(LITHIUM)* Fz 14324 23873 19098 15469
N 2090, 2091, 2099, 2195, 2199, 1 0.160 0.220
Feed (mm/min) 11459 12605
2297, 8090 RPM 29841 23873
Fz
Profile 0.5 0.160 0.220
Feed (mm/min)
14324 15756
Note: • maximum recommended depths shown
• surface speed is dependent on machine spindle & fixturing* • reduce speed and feed for materials harder than listed
• balancing is recommended at ultra high surface speeds • ramp angle = 15 (feed rate = 30%)
• tool life may be reduced when machining Lithium Alloys • maximum ramp depth = 1 x D1
• rpm = (1000 x m/min) / (3.14 x D1) • plunge depth = 1 x D1 (feed rate = 30%)
• mm/min = (mm / flute) x rpm •
6 sgs@sgs-tool.ru
www.sgs-tool.ru