SGS-Tools - Каталог для Европейских стран - 2014 EN

                                                                          для размещения заказа - sgs@sgs-tool.ru

Speed & Feed Recommendations

          43M, 43MCR, 43MCB,             CUT            SPEED                                                    FEED (mm/flute)
    47M, 47MES, 47MB, 47MEB, 44M
                                         Type           m/min            3 6 10 12 20 25
                 Metric
                                         Slot            490           0.022 0.060 0.120 0.144 0.187 0.213
 ALUMINUM ALLOY                       Profile          610           0.022 0.060 0.120 0.144 0.187 0.213
     2024, 5052, 5086,                  Light           1005           0.050 0.132 0.280 0.336 0.440 0.488
     6061, 6063, 7075                    Slot            185           0.022 0.060 0.120 0.144 0.187 0.213
                                        Profile          230           0.022 0.060 0.120 0.144 0.187 0.213
 ALUMINUM DIE CAST ALLOY              Light            380           0.050 0.132 0.280 0.336 0.440 0.488
     (High Silicon)                      Slot            265           0.019 0.048 0.107 0.120 0.160 0.175
     A-390, A-392, B-390                Profile          330           0.019 0.048 0.107 0.120 0.160 0.175
                                        Light            545           0.041 0.108 0.227 0.276 0.373 0.400
 COPPER ALLOY                          Slot            105           0.019 0.048 0.107 0.120 0.160 0.175
     Aluminum Bronze, Muntz             Profile          130           0.019 0.048 0.107 0.120 0.160 0.175
     Brass, Naval Brass, Red Brass      Light            215           0.041 0.108 0.227 0.276 0.373 0.400
                                         Slot            490           0.036 0.096 0.200 0.240 0.320 0.350
 COPPER ALLOY                         Profile          610           0.036 0.096 0.200 0.240 0.320 0.350
     Beryllium Copper, C110, Manganese  Light           1005           0.082 0.216 0.453 0.552 0.733 0.800
     Bronze, Tin Bronze

 PLASTIC
     ABS, Polycarbonate,
     PVC, Polypropylene

                SLOT                    CUT TYPE                                        LIGHT*                     rpm = (1000 x m/min) / (3.14 x D1)
                                        PROFILE                                                                    mm/min = (mm/flute) x rpm
                                                                                                                   • maximum recommended depths shown
Short, Regular  Long Reach,             Short, Regular  Long Reach,    Short, Regular,  Long Flute, Extra          • reduce speed and feed for materials harder than listed
ap = 0.6 x D1   Long Flute              ap = L2         Long Flute     Long Reach       Long Flute                 * finish cuts typically require reduced feed and cutting
ae = D1         ap = 0.5 x D1           ae = 0.5 x D1   ap = 1.5 x D1  ap = L2          ap = 3 x D1
                ae = D1                                 ae = 0.3 x D1  ae = 0.05 x D1   ae = 0.02 x D1              depths of 0.02 x D1 maximum
                                                                                                                   • refer to the SGS Tool Wizard for more complete technical

                                                                                                                    information (available at )
                                                                                                                   • Series 43 ramp angle = 15° (feed rate = 30 – 50%)

                                                                                                                    max. ramp depth = 1xD
                                                                                                                   • Series 43 plunge depth = 1xD (feed rate = 30%)
                                                                                                                   • Series 47 & 44 ramp angle = 15° (feed rate = 30%)

                                                                                                                    max. ramp depth = 1xD
                                                                                                                   • Series 47 & 44 plunge depth = 1xD (feed rate = 20%)

56 END MILLS

                                                                                sgs@sgs-tool.ru www.sgs-tool.ru