Фрезы и прочий твердосплавный инструмент
SGS-Tools - Каталог для Европейских стран - 2014 EN
для размещения заказа - sgs@sgs-tool.ru
Speed & Feed Recommendations
66M, 66MCR HARDNESS CUT SPEED FEED (mm/flute)
Metric BRINELL Type
m/min 6 8 10 12 16 20 25
CARBON STEEL 175 Profile
1018, 1040, 1080, 1090, 10L50, > 175 Light 174 0.022 0.034 0.043 0.053 0.061 0.069 0.075
1140, 1212, 12L15, 1525, 1536 275 Profile 0.105
275 Light 219 0.029 0.047 0.059 0.072 0.084 0.096 0.075
ALLOY STEEL > 275 Profile 0.105
4140, 4150, 4320, 5120, 5150, 375 Light 151 0.022 0.034 0.043 0.053 0.061 0.069 0.058
8630, 86L20, 50100 250 Profile 0.080
> 250 Light 192 0.029 0.047 0.059 0.072 0.084 0.096 0.058
TOOL STEEL 375 Profile 0.080
A2, D2, H13, L2, M2, 220 Light 126 0.017 0.028 0.035 0.041 0.049 0.053 0.053
P20, S7, T15, W2 > 220 Profile 0.073
260 Light 162 0.022 0.036 0.045 0.055 0.067 0.075 0.040
CAST IRON 275 Profile 0.055
Gray, Malleable, Ductile Light 87 0.017 0.028 0.035 0.041 0.049 0.053 0.075
275 Profile 0.105
STAINLESS (free machining) Light 110 0.022 0.036 0.045 0.055 0.067 0.075 0.075
303, 416, 420F, 430F, 440F 325 Profile 0.105
Light 113 0.014 0.023 0.029 0.036 0.044 0.048 0.058
STAINLESS (difficult) 350 Profile 0.080
304, 304L, 316, 316L Light 143 0.019 0.032 0.040 0.050 0.059 0.067 0.048
300 0.065
STAINLESS (PH) Profile 70 0.012 0.019 0.024 0.029 0.033 0.037
17-4PH, 15-5PH, Custom 450, 0.048
16-6PH, PH13-8Mo Light 88 0.014 0.026 0.032 0.038 0.046 0.051
0.065
TITANIUM Profile 169 0.022 0.034 0.043 0.053 0.061 0.069
Ti5Al-5V-5Mo, 0.053
Ti6Al4V, Ti-7Al4Mo Light 215 0.029 0.047 0.059 0.072 0.084 0.096
0.073
HIGH TEMPERATURE ALLOY Profile 126 0.022 0.034 0.043 0.053 0.061 0.069
A-286, Hastelloy, Incoloy, Inconel, 0.048
Rene, Waspalloy Light 160 0.029 0.047 0.059 0.072 0.084 0.096
0.065
131 0.017 0.028 0.035 0.041 0.049 0.053
171 0.022 0.036 0.045 0.055 0.067 0.075
93 0.012 0.021 0.027 0.031 0.038 0.043
117 0.017 0.030 0.037 0.043 0.051 0.059
85 0.012 0.021 0.027 0.031 0.038 0.043
108 0.017 0.030 0.037 0.043 0.051 0.059
93 0.014 0.023 0.029 0.036 0.044 0.048
119 0.019 0.032 0.040 0.050 0.059 0.067
26 0.012 0.021 0.027 0.031 0.038 0.043
33 0.017 0.030 0.037 0.043 0.051 0.059
CUT TYPE rpm = (1000 x m/min) / (3.14 x D1)
mm/min = (mm/flute) x no. of flutes x rpm
PROFILE LIGHT* • maximum recommended depths shown
• reduce speed and feed for materials harder than listed
ap = D1 ap = D1 * finish cuts typically require reduced feed and cutting depths of 0.02 x D1 maximum
ae = 0.1 x D1 ae = 0.05 x D1 • refer to the SGS Tool Wizard for more complete technical
information (available at )
• Ramping not recommended
38 END MILLS
sgs@sgs-tool.ru www.sgs-tool.ru