Фрезы и прочий твердосплавный инструмент
SGS-Tools - Полный каталог инструмента - 2014 EN
для размещения заказа - sgs@sgs-tool.ru
Speed & Feed Recommendations
Ap
Series Hardness Ae Ae Vc 3 6 8 Diameter (D1) 16 20 25
Z1MPCR, Z1MPLC BRINELL Ae x D1 Ap x D1 (m/min) 10987 5493 4120 (mm) 2060 1648 1318
Metric 0.014 0.023 0.046 0.051 0.050
STAINLESS STEELS Profile 104 RPM 316 387 10 12 380 334 264
M (Difficult) 4362 3272 3296 2747 1636 1309 1047
304, 304L,316, 316L 0.5 1.5 Fz 0.005 0.014 0.023 0.029 0.034 0.046 0.051 0.050
(83-124) 251 307 387 369 302 265 209
275 Feed (mm/min) 211 5009 3756 2617 2181 1878 1503 1202
0.014 0.023 0.029 0.034 0.046 0.051 0.050
Slot 82 RPM 8725 288 353 307 293 346 305 240
4039 3029 3005 2504 1515 1212 969
1 1 Fz 0.005 0.014 0.023 0.029 0.034 0.046 0.051 0.050
(66-99) 233 284 353 337 279 246 194
Feed (mm/min) 168 1293 969 2424 2020 485 388 310
0.010 0.017 0.029 0.034 0.033 0.037 0.038
Profile 94 RPM 10017 50 66 284 271 65 58 47
1050 788 776 646 394 315 252
STAINLESS STEELS (PH) < 325 0.5 1.5 Fz 0.005 0.010 0.017 0.021 0.024 0.033 0.037 0.038
M 13-8 PH,15-5PH,17-4 PH, 1 (76-113) 40 54 66 62 52 47 38
Feed (mm/min) 192 1002 751 630 525 376 301 240
Custom 450 0.007 0.011 0.021 0.024 0.023 0.027 0.028
Slot 76 RPM 8078 29 32 54 50 35 32 26
808 606 601 501 303 242 194
1 Fz 0.005 0.007 0.011 0.013 0.017 0.023 0.027 0.028
(61-91) 23 26 32 34 28 26 21
Feed (mm/min) 155 3474 2605 485 404 1303 1042 834
0.012 0.021 0.013 0.017 0.041 0.045 0.045
Profile 24 RPM 2585 167 222 26 27 213 189 150
2747 2060 2084 1737 1030 824 659
Super Alloys 0.5 1.5 Fz 0.004 0.012 0.021 0.027 0.031 0.041 0.045 0.045
(Nickel, Cobalt, (20-29) 132 176 222 217 169 149 119
S Iron Base) 300 Feed (mm/min) 37 1212 909 1648 1373 454 364 291
Inconel 601, 617, 625, 0.012 0.021 0.027 0.031 0.041 0.045 0.045
Incoly 800, Monel 400 Slot 20 RPM 2100 58 78 176 171 74 66 52
969 727 727 606 364 291 233
1 1 Fz 0.004 0.012 0.021 0.027 0.031 0.041 0.045 0.045
(16-24) 47 62 78 76 60 53 42
Feed (mm/min) 30 582 485
0.027 0.031
Profile 19 RPM 2003 62 60
Super Alloys 0.5 1.5 Fz 0.002
(15-23)
(Nickel, Cobalt, Feed (mm/min) 19
Iron Base)
S Inconel 718, 750X, > 300 15 RPM 1616
Incoly 925, Waspaloy, Slot
Hastelloy, Rene
1 1 Fz 0.002
(12-18)
Feed (mm/min) 16
Profile 66 RPM 6947
0.5 1.5 Fz 0.005
(52-79)
Titanium AlloyS Feed (mm/min) 133
Pure Ttanium, Ti6Al4V,
S Ti6Al2Sn4Zr2Mo, 350 52 RPM 5493
Ti4Al4Mo2Sn0.5Si Slot
1 1 Fz 0.005
(41-62)
Feed (mm/min) 105
Profile 23 RPM 2424
Slot
Titanium AlloyS 0.5 1.5 Fz 0.005
(DifFicult) 1 (18-27)
Ti10Al2Fe3Al, Feed (mm/min) 47
Ti5Al5V5Mo3Cr, > 350
S Ti7Al4Mo, 440 18 RPM 1939
Ti3Al8V6Cr4Zr4Mo,
Ti6Al6V6Sn, Ti15V3
Cr3Sn3Al 1 Fz 0.005
(15-22)
Feed (mm/min) 37
rpm = (1000 x m/min) / (3.14 x D1)
mm / min = (mm / flute) x 4 x rpm
maximum Slotting Ap for Z1PLC / Z1PLB is .25 x D1
maximum Profile Ae for Z1PLC / Z1PLB is .2 x D1
reduce speed and feed for materials harder than listed
reduce feed and Ae when finish milling (.02 x D1 maximum)
refer to the SGS Tool Wizard for complete technical information ()
END MILLS END MILLS 63
sgs@sgs-tool.ru
www.sgs-tool.ru