Фрезы и прочий твердосплавный инструмент
SGS-Tools - Полный каталог инструмента - 2014 EN
для размещения заказа - sgs@sgs-tool.ru
Speed & Feed Recommendations
Ap
Series Ae Ae Vc Diameter (D1)
Z1PCR, Z1PLC, Z1PLB Hardness Ae x D1 Ap x D1 (SFM) (inch)
Fractional 1/8 1/4 3/4 1
BRINELL 1.5 340 10390 5195 3/8 1/2 5/8 1732 1299
0.0002 0.0006 3463 2598 2078 0.0019 0.0020
Profile 0.5 (272-408) RPM 12.5 0.0011 0.0014 0.0018 13.2 10.4
Fz 8.3 4126 15.2 14.5 15.0 1375 1031
STAINLESS STEELS 275 270 Feed (IPM) 8251 0.0006 2750 2063 1650 0.0019 0.0020
M (Difficult) 1 RPM 0.0002 9.9 0.0011 0.0014 0.0018 10.5 8.3
Slot Fz 6.6 4737 12.1 11.6 11.9 1579 1184
304, 304L,316, 316L (216-324) Feed (IPM) 9474 0.0006 3158 2368 1895 0.0019 0.0020
RPM 0.0002 11.4 0.0011 0.0014 0.0018 12.0 9.5
1 Fz 7.6 3820 13.9 13.3 13.6 1273 955
Feed (IPM) 7640 0.0006 2547 1910 1528 0.0019 0.0020
Profile 0.5 310 RPM 0.0002 9.2 0.0011 0.0014 0.0018 9.7 7.6
1 1.5 Fz 6.1 1222 11.2 10.7 11.0 407 306
STAINLESS STEELS (PH) < 325 Feed (IPM) 2445 0.0004 815 611 489 0.0014 0.0015
M 13-8 PH,15-5PH,17-4 PH, (248-372) RPM 0.0002 2.0 0.0008 0.0010 0.0013 2.3 1.8
Slot Fz 1.5 993 2.6 2.4 2.5 331 248
Custom 450 250 Feed (IPM) 1986 0.0004 662 497 397 0.0014 0.0015
1 RPM 0.0002 1.6 0.0008 0.0010 0.0013 1.9 1.5
Fz 1.2 947 2.1 2.0 2.1 316 237
(200-300) Feed (IPM) 1895 0.0003 632 474 379 0.0010 0.0011
RPM 0.0001 1.1 0.0005 0.0007 0.0009 1.3 1.0
Profile 0.5 80 Fz 0.8 764 1.3 1.3 1.4 255 191
1.5 Feed (IPM) 1528 0.0003 509 382 306 0.0010 0.0011
Super Alloys 300 RPM 0.0001 0.9 0.0005 0.0007 0.0009 1.0 0.8
(Nickel, Cobalt, (64-96) Fz 0.6 3285 1.0 1.1 1.1 1095 821
S Iron Base) Slot 1 Feed (IPM) 6570 0.0005 2190 1643 1314 0.0017 0.0018
Inconel 601, 617, 625, 65 RPM 0.0002 6.6 0.0010 0.0013 0.0016 7.4 5.9
Incoly 800, Monel 400 1 Fz 5.3 2598 8.8 8.5 8.4 866 649
Feed (IPM) 5195 0.0005 1732 1299 1039 0.0017 0.0018
(52-78) RPM 0.0002 5.2 0.0010 0.0013 0.0016 5.9 4.7
Fz 4.2 1146 6.9 6.8 6.6 382 287
Profile 0.5 62 Feed (IPM) 2292 0.0005 764 573 458 0.0017 0.0018
1.5 RPM 0.0002 2.3 0.0010 0.0013 0.0016 2.6 2.1
Super Alloys Fz 1.8 917 3.1 3.0 2.9 306 229
(Nickel, Cobalt, (50-74) Feed (IPM) 1834 0.0005 611 458 367 0.0017 0.0018
Iron Base) RPM 0.0002 1.8 0.0010 0.0013 0.0016 2.1 1.7
S Inconel 718, 750X, > 300 50 Fz 1.5 2.4 2.4 2.3
1 Feed (IPM)
Incoly 925, Waspaloy, Slot
Hastelloy, Rene (40-60)
1
Profile 0.5 215
1.5
Titanium AlloyS
Pure Ttanium, Ti6Al4V, (172-258)
S Ti6Al2Sn4Zr2Mo, 350
170
Ti4Al4Mo2Sn0.5Si Slot 1
1 (136-204)
Titanium AlloyS Profile 0.5 75
(DifFicult) Slot 1 1.5
Ti10Al2Fe3Al,
Ti5Al5V5Mo3Cr, > 350 (60-90)
S Ti7Al4Mo, 440
60
Ti3Al8V6Cr4Zr4Mo, 1
Ti6Al6V6Sn, Ti15V3
Cr3Sn3Al (48-72)
rpm = sfm x 3.82 / D1
ipm = (inch / flute) x 4 x rpm
maximum Slotting Ap for Z1PLC / Z1PB is .25 x D1
maximum Profile Ae for Z1PLC / Z1PLB is .2 x D1
reduce speed and feed for materials harder than listed
reduce feed and Ae when finish milling (.02 x D1 maximum)
refer to the SGS Tool Wizard for complete technical information ()
END MILLS END MILLS 61
sgs@sgs-tool.ru
www.sgs-tool.ru