для размещения заказа - sgs@sgs-tool.ru
Speed & Feed Recommendations
Z1PCR, Z1PLC, Z1PLB HARDNESS CUT SPEED 1/16 1/8 FEED (inch/flute) 3/4 1
Fractional BRINELL
Type sfm 0.00019 0.00047 1/4 3/8 1/2 0.0037 0.0043
CARBON STEEL 175 0.00019 0.00047 0.0037 0.0043
1018, 1040, 1080, 1090, Slot 505 0.00044 0.00107 0.0012 0.0023 0.0031 0.0085 0.0100
10L50, 1140, 1212, 12L15, > 175 Profile 630 0.00019 0.00047 0.0012 0.0023 0.0031 0.0037 0.0043
1525, 1536 275 Light 1040 0.00019 0.00047 0.0028 0.0053 0.0071 0.0037 0.0043
Slot 440 0.00044 0.00107 0.0012 0.0023 0.0031 0.0085 0.0100
ALLOY STEEL 275 Profile 550 0.00014 0.00035 0.0012 0.0023 0.0031 0.0028 0.0032
4140, 4150, 4320, 5120, Light 910 0.00014 0.00035 0.0028 0.0053 0.0071 0.0028 0.0032
5150, 8630, 86L20, 50100 > 275 Slot 370 0.00033 0.00079 0.0009 0.0017 0.0023 0.0063 0.0074
375 Profile 465 0.00014 0.00035 0.0009 0.0017 0.0023 0.0028 0.0032
Light 765 0.00014 0.00035 0.0021 0.0040 0.0053 0.0028 0.0032
TOOL STEEL 250 Slot 250 0.00033 0.00079 0.0009 0.0017 0.0023 0.0063 0.0074
A2, D2, H13, L2, M2, Profile 315 0.00014 0.00035 0.0009 0.0017 0.0023 0.0028 0.0032
P20, S7, T15, W2 > 250 Light 520 0.00014 0.00035 0.0021 0.0040 0.0053 0.0028 0.0032
375 Slot 240 0.00033 0.00079 0.0009 0.0017 0.0023 0.0063 0.0074
Profile 300 0.00011 0.00027 0.0009 0.0017 0.0023 0.0022 0.0025
CAST IRON 220 Light 495 0.00011 0.00027 0.0021 0.0040 0.0053 0.0022 0.0025
Gray, Malleable, Ductile Slot 145 0.00026 0.00062 0.0007 0.0014 0.0018 0.0050 0.0058
> 220 Profile 185 0.00018 0.00042 0.0007 0.0014 0.0018 0.0034 0.0039
260 Light 305 0.00018 0.00042 0.0017 0.0031 0.0041 0.0034 0.0039
Slot 355 0.00040 0.00096 0.0011 0.0021 0.0028 0.0077 0.0090
STAINLESS (free machining) 275 Profile 445 0.00018 0.00042 0.0011 0.0021 0.0028 0.0034 0.0039
303, 416, 420F, 430F, 440F Light 730 0.00018 0.00042 0.0026 0.0048 0.0064 0.0034 0.0039
Slot 265 0.00040 0.00096 0.0011 0.0021 0.0028 0.0077 0.0090
STAINLESS (difficult) 275 Profile 330 0.00014 0.00035 0.0011 0.0021 0.0028 0.0028 0.0032
304, 304L, 316, 316L 325 Light 545 0.00014 0.00035 0.0026 0.0048 0.0064 0.0028 0.0032
350 Slot 455 0.00033 0.00079 0.0009 0.0017 0.0023 0.0063 0.0074
STAINLESS (PH) 300 Profile 570 0.00011 0.00027 0.0009 0.0017 0.0023 0.0022 0.0025
17-4PH, 15-5PH, Custom Light 935 0.00011 0.00027 0.0021 0.0040 0.0053 0.0022 0.0025
450, 16-6PH, PH13-8Mo Slot 315 0.00026 0.00062 0.0007 0.0014 0.0018 0.0050 0.0058
Profile 395 0.00011 0.00027 0.0007 0.0014 0.0018 0.0022 0.0025
TITANIUM Light 650 0.00011 0.00027 0.0017 0.0031 0.0041 0.0022 0.0025
Ti5Al-5V-5Mo, Slot 290 0.00026 0.00062 0.0007 0.0014 0.0018 0.0050 0.0058
Ti6Al4V, Ti-7Al4Mo Profile 360 0.00013 0.00030 0.0007 0.0014 0.0018 0.0024 0.0028
Light 595 0.00013 0.00030 0.0017 0.0031 0.0041 0.0024 0.0028
HIGH TEMPERATURE ALLOY Slot 170 0.00029 0.00069 0.0008 0.0015 0.0020 0.0055 0.0064
A-286, Hastelloy, Incoloy, Profile 215 0.00009 0.00023 0.0008 0.0015 0.0020 0.0018 0.0021
Inconel, Rene, Waspalloy Light 355 0.00009 0.00023 0.0018 0.0034 0.0046 0.0018 0.0021
Slot 65 0.00022 0.00052 0.0006 0.0011 0.0015 0.0041 0.0048
Profile 80 0.0006 0.0011 0.0015
Light 130 0.0014 0.0026 0.0034
SLOT CUT TYPE LIGHT* rpm = sfm x 3.82 / D1
PROFILE ipm = (inch/flute) x rpm
Long Reach Regular, Long Reach
Regular Rw = D1 Regular Long Reach Rw = .05 x D1 • maximum recommended depths shown
Rw = D1 Ad = .25 x D1 Rw = .5 x D1 Rw = .2 x D1 Ad = L2 • reduce speed and feed for materials harder
Ad = D1 Ad = 1.5 x D1 Ad = 1.5 x D1
than listed
* finish cuts typically require reduced feed
and cutting depths of .02 x D1 maximum
•refer to the SGS Tool Wizard for more
complete technical information
(available at )
END MILLS END MILLS 57
sgs@sgs-tool.ru
www.sgs-tool.ru
