SGS-Tools - Полный каталог инструмента - 2013 EN
для размещения заказа - sgs@sgs-tool.ru
SGS Reference Information
EDP NO. PAGE EDP NO. PAGE EDP NO. PAGE EDP NOI.S O PHA6GSEPECIFIECDAPTINOON. S PAGE EDP NO. PAGE EDP NO. PAGE EDP NO. PAGE
DIAMETER + – DIAMETER + –
1/8 - 3/16 0.00000 –0.00032 3 0,000 0,006
> 3/16 - 7/16 0.00000 0,000 0,008
> 7/16 - 5/8 0.00000 –0.00035 >3-6 0,000 0,009
0.00000 0,000 0,011
> 5/8 - 1 0.00000 –0.00043 > 6 - 10 0,000 0,013
> 1 - 1-1/4
–0.00051 > 10 - 18
–0.00063 > 18 - 25
MACHINING FORMULAS
INCH FORMULAS METRIC FORMULAS
sfm = rpm x .262 x cutting diameter m/min = (3.14 x cutting diameter x rpm) / 1000
rpm = sfm x 3.82 / cutting diameter rpm = (1000 x m / min) / (3.14 x cutting diameter)
feed (inches per tooth) = ipm / ( number of teeth x rpm) feed (mm per tooth) = millimeters per minute / (number of teeth x rpm)
feed (inches / minute) = inches per tooth x number of teeth x rpm feed (mm/minute) = feed per tooth x number of teeth x rpm
feed (inches / minute) = ipr x rpm feed (mm/minute) = mmr x rpm
feed (inches / revolution) = ipm / rpm feed (mm per revolution) = mmr / rpm
cusp height* = (tool diameter / 2) – (tool diameter2 – pitch2) / 4 cusp height* = (tool diameter / 2) – (tool diameter2 – pitch2) / 4
pitch = 4 x (cusp height x tool diameter) – 4 x (cusp height2) pitch = 4 x (cusp height x tool diameter) – 4 x (cusp height2)
mrr – milling – (in3/min) = width of cut x depth of cut x ipm mrr – milling – (cm3/min) = (width of cut x depth of cut x mm/min) / 1000
cutting time – drilling – (minutes) = length / ipm cutting time – drilling – (minutes) = length / mm/min
sfm surface feet per minute
rpm revolutions per minute
ipm feed rate in inches per minutes
ipr inches per revolution
mmr millimeters per revolution
mm/min feed rate in millimeters per
minute
mrr material removal rate
* on flat surface
GENERAL FORMULAS
coolant pressure: 1 Bar = 14.5 Pounds per Square Inch (PSI)
calculation of coolant pressure: Pounds Per Square Inch (PSI) = (Horsepower of Pump x 1.460) / Gallons per Minute (GPM)
1 Liter = 0.254 Gallons
inch = millimeters / 25.4 millimeters = inch x 25.4
inch tap drill sizes = major diameter – ((1.299 x % of thread) / threads per inch)
metric tap drill sizes = major diameter – (1.082 x pitch x % of thread)
inch thread forming drill size: maximum diameter = basic major diameter – (3/8 x number of threads per inch)
inch thread forming drill size: minimum diameter = basic major diameter – (1/2 x number of threads per inch)
metric thread forming drill size: maximum diameter = basic major diameter – (.375 x pitch)
metric thread forming drill size: minimum diameter = basic major diameter – (.500 x pitch)
225
sgs@sgs-tool.ru
www.sgs-tool.ru
