для размещения заказа - sgs@sgs-tool.ru
Speed & Feed Recommendations
Series 135 3xD HARDNESS SPEED 1/64 1/32 1/16 FEED (inch/rev) 1/2 5/8 7/8
Fractional BRINELL sfm 1/8 1/4 3/8
0.00050 0.0010 0.0020 0.0160 0.0200 0.0280
C ARBON STEEL 200 400 0.0040 0.0080 0.0120
1018, 1040, 1080, 1090,
10L50, 1140, 1212, 12L15, > 200 350 0.00045 0.0009 0.0018 0.0035 0.0070 0.0105 0.0140 0.0175 0.0245
1525, 1536 300
> 300 160 0.00035 0.0008 0.0015 0.0030 0.0060 0.0090 0.0120 0.0150 0.0210
A LLOY STEEL 420
4140, 4150, 4320, 4340, 300 0.00035 0.0008 0.0015 0.0030 0.0060 0.0090 0.0120 0.0150 0.0210
5120, 5150, 8630, 86L20, 270
50100, 52100 220 0.00030 0.0006 0.0013 0.0025 0.0050 0.0075 0.0100 0.0125 0.0175
> 270
T OOL STEEL 370 120 0.00020 0.0005 0.0009 0.0018 0.0035 0.0055 0.0070 0.0090 0.0125
A2, D2, H13, L2, M2, > 370
P20, S7, T15, W2 450 220 0.00030 0.0006 0.0013 0.0025 0.0050 0.0075 0.0100 0.0125 0.0175
CAST IRON 250 150 0.00020 0.0005 0.0009 0.0018 0.0035 0.0055 0.0070 0.0090 0.0125
Gray, Malleable, Ductile
> 250 70 0.00010 0.0003 0.0005 0.0010 0.0020 0.0030 0.0040 0.0050 0.0070
S TAINLESS (free machining) 330
303, 416, 420F, 430F, 440F > 330 400 0.00060 0.0013 0.0025 0.0050 0.0100 0.0150 0.0200 0.0250 0.0350
450
S TAINLESS (difficult) 250 0.00055 0.0011 0.0023 0.0045 0.0090 0.0135 0.0180 0.0225 0.0315
304, 316, 321, 15-5ph, 200
17-4PH, Nitronic 32 200 0.00030 0.0006 0.0013 0.0025 0.0050 0.0075 0.0100 0.0125 0.0175
> 200
T ITANIUM 330 150 0.00025 0.0005 0.0010 0.0020 0.0040 0.0060 0.0080 0.0100 0.0140
TiCODE-12, Ti-6Al4V,
Ti-5Al-5V-5Mo-3Cr, 250 90 0.00020 0.0005 0.0009 0.0018 0.0035 0.0055 0.0070 0.0090 0.0125
Ti-7Al4Mo, Ti8Al1Mo1V
> 250 70 0.00020 0.0004 0.0008 0.0015 0.0030 0.0045 0.0060 0.0075 0.0105
H IGH TEMPERATURE ALLOY 330
A-286, Hastelloy, 120 0.00020 0.0005 0.0009 0.0018 0.0035 0.0055 0.0070 0.0090 0.0125
Haynes, Incoloy, Inconel, 270
Rene, Waspalloy 100 0.00020 0.0004 0.0008 0.0015 0.0030 0.0045 0.0060 0.0075 0.0105
> 270
A LUMINUM 370 70 0.00015 0.0003 0.0007 0.0013 0.0025 0.0040 0.0050 0.0065 0.0090
2017, 2024, 356,
6061, 7075 280 60 0.00010 0.0003 0.0005 0.0010 0.0020 0.0030 0.0040 0.0050 0.0070
> 280 40 0.00010 0.0002 0.0004 0.0008 0.0015 0.0025 0.0030 0.0040 0.0055
350
> 350 30 0.00005 0.0001 0.0003 0.0005 0.0010 0.0015 0.0020 0.0025 0.0035
440
700 0.00070 0.0014 0.0028 0.0055 0.0110 0.0165 0.0220 0.0275 0.0385
220
600 0.00060 0.0013 0.0025 0.0050 0.0100 0.0150 0.0200 0.0250 0.0350
> 220
330
> 330
420
80
> 80
C OPPER ALLOY 140 500 0.00025 0.0005 0.0010 0.0020 0.0040 0.0060 0.0080 0.0100 0.0140
Alum Bronze, C110, > 140
Muntz Brass 400 0.00025 0.0005 0.0010 0.0020 0.0040 0.0060 0.0080 0.0100 0.0140
Reduce speed & feed for materials rpm = sfm 3.82 / D1 Refer to the SGS Tool Wizard for more complete
harder than listed ipm = (inch/rev) rpm technical information (available at )
DRILLS DRILLS 149
sgs@sgs-tool.ru
www.sgs-tool.ru
