Фрезы и прочий твердосплавный инструмент
SGS-Tools - Multi-carb - Фрезы для чистовой обработки - 2014 EN
для размещения заказа - sgs@sgs-tool.ru | Speed & Feed Recommendations
Multi-Carb
Ae
Hardness Series 66, 66CR Ap Vc 3/16 1/4 Diameter (inch) 3/4 1
BRINELL Fractional Ap x D1 Ae x D1 (SFM) 5883 3/8 1/2 5/8 1961 1471
0.0007 3922 2941 2353 0.0022 0.0026
Profile 1 0.05 385 RPM 7844 29 0.0014 0.0018 0.0020 47 42
7059 38 48 42 2353 1765
185 STAINLESS STEEL Fz 0.0005 0.0006 4706 3530 2824 0.0018 0.0021
(DIFFICULT) (308-462) 28 0.0011 0.0014 0.0016 46 40
304, 304L, 316, 316L 37 46 41 1808 1356
Feed (IPM) 27 0.0022 0.0026
44 39
Finish 462 RPM 9412 2170 1627
0.0018 0.0021
2 0.02 (370-554) Fz 0.0004 42 37
535 401
Feed (IPM) 26 0.0022 0.0026
12.9 11.5
Profile 355 RPM 7233 5424 3616 2712 2170 642 481
0.0018 0.0021
1 0.05 (284-426) Fz 0.0005 0.0007 0.0014 0.0018 0.0020 12.4 11.0
433 325
325 STAINLESS STEEL Feed (IPM) 25 27 35 44 39 0.0015 0.0017
(PH) 7.1 6.1
13-8 PH, 15-5PH, 17-4 PH, Finish 426 RPM 8679 6509 4340 3255 2604 520 390
Custom 450 0.0012 0.0014
6.9 5.8
2 0.02 (341-511) Fz 0.0004 0.0006 0.0011 0.0014 0.0016 1986 1490
0.0025 0.0029
Feed (IPM) 24 26 34 42 37 55 48
2384 1788
Profile 105 RPM 2139 1604 1070 802 642 0.0020 0.0023
52 46
1 0.05 (84-126) Fz 0.0005 0.0007 0.0014 0.0018 0.0020 713 535
0.0025 0.0029
300 SUPER ALLOYS Feed (IPM) 7.5 7.9 10.5 13.0 11.6 20 17
(NICKEL, COBALT, IRON BASED) 856 642
Inconel 601, 617, 625, Incoly 800, Finish 126 RPM 2567 1925 1284 963 770 0.0020 0.0023
Monel 400 19 16
2 0.02 (101-151) Fz 0.0004 0.0006 0.0011 0.0014 0.0016
Feed (IPM) 7.2 7.5 10.1 12.5 11.1
Profile 85 RPM 1732 1299 866 649 520
SUPER ALLOYS 1 0.05 (68-102) Fz 0.0003 0.0005 0.0009 0.0012 0.0014
(NICKEL, COBALT, IRON BASED –
> 300 DIFFICULT) Feed (IPM) 3.9 4.5 5.6 7.0 6.4
Inconel 718, 750X, Incoly 925,
Waspaloy, Hastelloy, Rene Finish 102 RPM 2078 1559 1039 779 623
2 0.02 (82-122) Fz 0.0002 0.0004 0.0007 0.0010 0.0011
Feed (IPM) 2.9 4.3 5.4 6.7 6.1
Profile 390 RPM 7946 5959 3973 2980 2384
1 0.05 Fz 0.0005 0.0008 0.0015 0.0021 0.0023
(312-468)
TITANIUM ALLOYS Feed (IPM) 28 33 42 56 49
350 Pure Titanium, Ti6Al4V,
Ti6Al2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si 468 RPM 9535 7151 4767 3576 2860
Finish
2 0.02 Fz 0.0004 0.0006 0.0012 0.0017 0.0018
(374-562)
Feed (IPM) 27 32 40 54 47
Profile 140 RPM 2852 2139 1426 1070 856
1 0.05 Fz 0.0005 0.0008 0.0015 0.0021 0.0023
(112-168)
TITANIUM ALLOYS Feed (IPM) 10 12 15 20 18
> 350 (DIFFICULT)
450 Ti10Al2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo,
Ti3Al8V6Cr4Zr4Mo, Ti6Al6V6Sn, Ti15V3 Finish 168 RPM 3423 2567 1711 1284 1027
2 0.02 (134-202) Fz 0.0004 0.0006 0.0012 0.0017 0.0018
Feed (IPM) 10 12 14 19 17
*Maximum recommended depth shown
*Reduce speed and feed recommendations for materials harder than listed
*Above recommendations are based on ideal conditions. Adjust parameters accordingly for smaller taper machining centers or less rigid conditions
*
sgs@sgs-tool.ru 9
www.sgs-tool.ru