Фрезы и прочий твердосплавный инструмент
SGS-Tools - Multi-carb - Фрезы для чистовой обработки - 2014 EN
для размещения заказа - sgs@sgs-tool.ru | Speed & Feed Recommendations
Multi-Carb
Ae
Hardness Series 66M, 66MCR Ap Vc 6 8 Diameter (mm) 20 25
BRINELL Metric Ap x D1 Ae x D1 (m/min) 6202 4651 10 12 16 1861 1488
0.022 0.036 3721 3101 2326 0.075 0.080
Profile 1 0.05 117 RPM 955 1172 0.045 0.055 0.067 1535 1310
5582 1172 1535 1402 2233 1786
185 STAINLESS STEEL Fz 0.029 4465 3721 2791 0.060 0.064
(DIFFICULT) (94-140) 1125 0.036 0.044 0.054 1474 1257
304, 304L, 316, 316L 1125 1474 1346 1717 1374
Feed (mm/min) 0.059 0.065
1115 982
Finish 140 RPM 7442 2061 1649
0.047 0.052
2 0.02 (112-168) Fz 0.018 1070 943
509 407
Feed (mm/min) 917 0.059 0.065
330 291
Profile 108 RPM 5725 4294 3435 2862 2147 611 489
0.047 0.052
1 0.05 (86-130) Fz 0.017 0.030 0.037 0.043 0.051 317 279
413 331
325 STAINLESS STEEL Feed (mm/min) 681 902 890 1108 985 0.039 0.044
(PH) 176 159
13-8 PH, 15-5PH, 17-4 PH, Finish 130 RPM 6870 5152 4122 3435 2576 496 397
Custom 450 0.031 0.035
169 153
2 0.02 (104-156) Fz 0.014 0.024 0.030 0.034 0.041 1892 1514
0.067 0.073
Feed (mm/min) 654 866 854 1063 946 1395 1216
2271 1817
Profile 32 RPM 1696 1272 1018 848 636 0.054 0.058
1339 1167
1 0.05 (26-38) Fz 0.017 0.030 0.037 0.043 0.051 684 547
0.067 0.073
300 SUPER ALLOYS Feed (mm/min) 202 267 214 328 292 504 439
(NICKEL, COBALT, IRON BASED) 821 656
Inconel 601, 617, 625, Incoly 800, Finish 38 RPM 2036 1527 1221 1018 763 0.054 0.058
Monel 400 484 422
2 0.02 (31-46) Fz 0.014 0.024 0.030 0.034 0.041
Feed (mm/min) 194 256 253 315 280
Profile 26 RPM 1378 1034 827 689 517
SUPER ALLOYS 1 0.05 (21-31) Fz 0.012 0.020 0.025 0.030 0.035
(NICKEL, COBALT, IRON BASED –
> 300 DIFFICULT) Feed (mm/min) 113 143 142 184 162
Inconel 718, 750X, Incoly 925,
Waspaloy, Hastelloy, Rene Finish 31 RPM 1654 1240 992 827 620
2 0.02 (25-37) Fz 0.009 0.016 0.020 0.024 0.028
Feed (mm/min) 108 138 137 177 155
Profile 119 RPM 6308 4731 3785 3154 2365
1 0.05 Fz 0.019 0.032 0.040 0.050 0.059
(95-143)
TITANIUM ALLOYS Feed (mm/min) 839 1060 1060 1419 1256
350 Pure Titanium, Ti6Al4V,
Ti6A2Sn4Zr2Mo, Ti4Al4Mo2Sn0.5Si 143 RPM 7570 5677 4542 3785 2839
Finish
2 0.02 Fz 0.015 0.026 0.032 0.040 0.047
(114-171)
Feed (mm/min) 805 1017 1017 1363 1206
Profile 43 RPM 2279 1710 1368 1140 855
1 0.05 Fz 0.019 0.032 0.040 0.050 0.059
(34-52)
TITANIUM ALLOYS Feed (mm/min) 303 383 383 513 454
> 350 (DIFFICULT)
450 Ti10Al2Fe3Al, Ti5Al5V5Mo3Cr, Ti7Al4Mo,
Ti3Al8V6Cr4Zr4Mo, Ti6Al6V6Sn, Ti15V3 Finish 52 RPM 2735 2051 1641 1368 1026
2 0.02 (41-62) Fz 0.015 0.026 0.032 0.040 0.047
Feed (mm/min) 291 368 368 492 436
*Maximum recommended depth shown
*Reduce speed and feed recommendations for materials harder than listed
*Above recommendations are based on ideal conditions. Adjust parameters accordingly for smaller taper machining centers or less rigid conditions
*
sgs@sgs-tool.ru 11
www.sgs-tool.ru