SGS-Tools - Каталог для Европейских стран - 2014 EN

                                                                          для размещения заказа - sgs@sgs-tool.ru

Speed & Feed Recommendations

7M, 7MB                         HARDNESS  CUT     SPEED  3                                                                FEED (mm/flute)
 Metric                          BRINELL  Type    m/min                                                 6 10 12 20 25

CARBON STEEL                     175 Finish      250    0.0166  0.043                                             0.093  0.110  0.147  0.160

1018, 1040, 1080, 1090, 10L50,  > 175
                                 275
1140, 1212, 12L15, 1525, 1536             Finish  220    0.0166  0.043                                             0.093  0.110  0.147  0.160

ALLOY STEEL                      275 Finish      185    0.0122  0.034                                             0.069  0.082  0.109  0.120

4140, 4150, 4320, 5120, 5150,   > 275
                                 375
8630, 86L20, 50100                        Finish  125    0.0122  0.034                                             0.069  0.082  0.109  0.120

TOOL STEEL                       250 Finish      170    0.0086  0.024                                             0.048  0.058  0.077  0.085
A2, D2, H13, L2, M2,
P20, S7, T15, W2                > 250     Finish  105    0.0070  0.019                                             0.040  0.048  0.064  0.070
                                 375

CAST IRON                        220 Finish      185    0.0132  0.036                                             0.075  0.089  0.117  0.130
Gray, Malleable, Ductile
                                > 220     Finish  135    0.0132  0.036                                             0.075  0.089  0.117  0.130
                                 260

STAINLESS (free machining)       275 Finish      130    0.0086  0.024                                             0.048  0.058  0.077  0.085
303, 416, 420F, 430F, 440F

STAINLESS (difficult)            275 Finish      90     0.0082  0.022                                             0.045  0.048  0.072  0.078
304, 304L, 316, 316L

STAINLESS (PH)

17-4PH, 15-5PH, Custom 450, 16-  325     Finish  80     0.0070  0.019                                             0.040  0.048  0.064  0.070

6PH, PH13-8Mo

TITANIUM                         350 Finish      90     0.0091  0.024                                             0.051  0.060  0.080  0.088
Ti5Al-5V-5Mo,
Ti6Al4V, Ti-7Al4Mo

HIGH TEMPERATURE ALLOY           300 Finish      25     0.0072  0.019                                             0.037  0.046  0.061  0.085
Inconel, Rene, Waspalloy

               CUT TYPE         rpm = (1000 x m/min) / (3.14 x D1)
                FINISH          mm/min = (mm/flute) x 4 x rpm
                                • maximum recommended depths shown
ap = L2                         • adjust feed as required for optimum results
ae = 0.02 x D1                  • reduce speed and feed for materials harder than listed
                                • refer to the SGS Tool Wizard for more complete technical information

                                 (available at )
                                • ramping not recommended

32 END MILLS

                                                                                sgs@sgs-tool.ru www.sgs-tool.ru